T100 Underwater Thruster Designed for Marine Robotics
From BlueRobotics' Kickstarter:
An efficient, rugged, affordable underwater thruster to propel the future of marine robotics and ocean exploration. ($100 dollars a thruster, est delivery Nov 2014)
The T100 is made of high-strength, UV resistant polycarbonate injection molded plastic. The core of the motor is sealed and protected with an epoxy coating and it uses high-performance plastic bearings in place of steel bearings that rust in saltwater. Everything that isn’t plastic is either aluminum or high-quality stainless steel that doesn’t corrode.
A specially designed propeller and nozzle provides efficient, powerful thrust while active water-cooling keeps the motor cool. Unlike other thrusters, our design doesn’t have any air- or oil-filled cavities - water flows freely through all parts of the motor while it's running. That means it can go deep in the ocean and handle extreme pressures.
The thruster is easy to use: just connect the three motor wires to any brushless electronic speed controller (ESC) and you can control it with an RC radio or a microcontroller. It's usable with Arduino, ArduPilot, Raspberry Pi, BeagleBone, and many other embedded platforms... (kickstarter)
Self-Folding Origami Robot Goes From Flat to Walking in Four Minutes
From IEEE Spectrum:
Printable, self-folding robot created by Harvard and MIT researchers... (IEEE Spectrum story) (full paper)
Hitchbot is Halfway Across its Canadian Journey
From hitchBOT's page:
I am hitchBOT — a robot from Port Credit, Ontario.
I am traveling from Halifax, Nova Scotia to Victoria, British Columbia this summer. As you may have guessed, robots cannot get driver’s licences yet, so I’ll be hitchhiking my entire way... (cont'd)
Nvidia Jetson TK1 Development Kit
Features ($192 ):
Tegra K1 SOC
Kepler GPU with 192 CUDA cores
4-Plus-1 quad-core ARM Cortex A15 CPU
2 GB x16 memory with 64 bit width
16 GB 4.51 eMMC memory
1 Half mini-PCIE slot
1 Full size SD/MMC connector
1 Full-size HDMI port
1 USB 2.0 port, micro AB
1 USB 3.0 port, A
1 RS232 serial port
1 ALC5639 Realtek Audio codec with Mic in and Line out
1 RTL8111GS Realtek GigE LAN
1 SATA data port
SPI 4MByte boot flash
Dr. Dobbs has an in depth look here.
Ino: Command Line Toolkit for Arduino Hardware
Ino tools webpage:
Ino is a command line toolkit for working with Arduino hardware
It allows you to:
Quickly create new projects
Build a firmware from multiple source files and libraries
Upload the firmware to a device
Perform serial communication with a device (aka serial monitor)
Ino may replace Arduino IDE UI if you prefer to work with command line and an editor of your choice or if you want to integrate Arduino build process to 3-rd party IDE.
Ino is based on make to perform builds. However Makefiles are generated automatically and you’ll never see them if you don’t want to.
Features
Simple. No build scripts are necessary.
Out-of-source builds. Directories with source files are not cluttered with intermediate object files.
Support for *.ino and *.pde sketches as well as raw *.c and *.cpp.
Support for Arduino Software versions 1.x as well as 0.x.
Automatic dependency tracking. Referred libraries are automatically included in the build process. Changes in *.h files lead to recompilation of sources which include them.
Pretty colorful output.
Support for all boards that are supported by Arduino IDE.
Fast. Discovered tool paths and other stuff is cached across runs. If nothing has changed, nothing is build.
Flexible. Support for simple ini-style config files to setup machine-specific info like used Arduino model, Arduino distribution path, etc just once.
(Homepage)
REMUS SharkCam: The Hunter and the Hunted
From Woods Hole Oceanographic Institution's Vimeo page:
In 2013, a team from the Woods Hole Oceanographic Institution took a specially equipped REMUS "SharkCam" underwater vehicle to Guadalupe Island in Mexico to film great white sharks in the wild. They captured more than they bargained for.
Additional article in Oceanus Magazine.
Robot With Broken Leg Learns To Walk Again In 2 Minutes
From Medium:
Today, Antoine Cully at the Sorbonne University in Paris and a couple of pals say they’ve developed a technique that allows a damaged robot to learn how to walk again in just a few seconds. They say their work has important consequences for the reliability and robustness of future robots and may also provide some insight into the way that animals adapt to injury as well... (cont'd)
JIBO
From JIBO's Indiegogo campaign:
Friendly, helpful and intelligent. From social robotics pioneer Dr. Cynthia Breazeal.
OpenFPV
From Tilman Griesel's posts on DIY Drones:
Open source project to make FPV(first person view) with the raspberry pi easy to use for every one.
OpenFPV is a project that uses latest technology to provide low latency, easy and well tested open source FPV flying. Based on single-board computers, HD cameras and IEEE 802.11.
Current Features:
Recording
Web interface
Low-Latency H264 Streaming (≈120ms)
RESTful API
Customizable
Extendable
Installer (in progress)
Minimal bettery consumption
Roadmap:
Invite more people to join the development team
Complete the installer
More field tests with different setups
Create desktop applications for mac/win with HUD support
Add OculusVR support
Release is not available yet but you can follow the progress on DIY Drones or the OpenFPV homepage.
Quoc Le's Lectures on Deep Learning
Gaurav Trivedi has put together a landing page with all of Quoc Le’s recent lecture series and accompanying resources:
Dr. Quoc Le from the Google Brain project team (yes, the one that made headlines for creating a cat recognizer) presented a series of lectures at the Machine Learning Summer School (MLSS ’14) in Pittsburgh this week. This is my favorite lecture series from the event till now and I was glad to be able to attend them... (cont'd with all videos)
Parallella: $119 Parallel Computing Platform with 16-core Epiphany chip
Parallella Computer Specifications:
The Parallella platform is an open source, energy efficient, high performance, credit-card sized computer based on the Epiphany multicore chips developed by Adapteva. This affordable platform is designed for developing and implementing high performance, parallel processing applications developed to take advantage of the on-board Epiphany chip. The Epiphany 16 or 64 core chips consists of a scalable array of simple RISC processors programmable in C/C++ connected together with a fast on chip network within a single shared memory architecture... (cont'd)
A realtime raytracing example running on the 16-core Epiphany chip:
Raspberry Pi Model B+
From Eben Upton, Raspberry Pi Founder:
This isn’t a “Raspberry Pi 2″, but rather the final evolution of the original Raspberry Pi. Today, I’m very pleased to be able to announce the immediate availability, at $35 – it’s still the same price, of what we’re calling the Raspberry Pi Model B+.
The Model B+ uses the same BCM2835 application processor as the Model B. It runs the same software, and still has 512MB RAM; but James and the team have made the following key improvements:
More GPIO. The GPIO header has grown to 40 pins, while retaining the same pinout for the first 26 pins as the Model B.
More USB. We now have 4 USB 2.0 ports, compared to 2 on the Model B, and better hotplug and overcurrent behaviour.
Micro SD. The old friction-fit SD card socket has been replaced with a much nicer push-push micro SD version.
Lower power consumption. By replacing linear regulators with switching ones we’ve reduced power consumption by between 0.5W and 1W.
Better audio. The audio circuit incorporates a dedicated low-noise power supply.
Neater form factor. We’ve aligned the USB connectors with the board edge, moved composite video onto the 3.5mm jack, and added four squarely-placed mounting holes... (cont'd)
Intro to Shape Memory Alloy Actuation Using Flexinol
From Jie Qi's projects page:
Shape memory alloys (SMAs) are metals that change shape when heated up. They are wonderful actuators in that they are light, silent and can be "turned on" by simply running current through. The shape that they change to can also be set, though this process is a bit more tricky. Flexinol is a particular brand of nitinol, which is an SMA made of nickel and titanium, and is pre-set to contract about 10% of its original length when heated.
In my projects, I generally used the 0.006" to 0.01" diameter, High-Temp wires.
Since Flexinol draws a lot of current (about 300mA for the diameters I used), you need a strong power supply like a wall supply or a good lithium-ion battery. I've used from 3.7V up to 6V (any more and my Flexinol wires would start overheating). To turn the Flexinol on, I would simply short the ends of the wire to the power. For digital control, I used a standard MOSFET circuit which is a digital switch that can be turned on and off using a microcontroller... (cont'd)
BugJuggler: Project to build 70ft tall robot that juggles cars
Project Overview:
BugJuggler will use a diesel engine to generate hydraulic pressure. An operator located in the robot’s head will be able to control its motions using a haptic feedback interface connected to high-speed servo valves. Hydraulic accumulators - essentially storage batteries for hydraulic fluid - will allow for the rapid movement required for the robot to juggle cars or other large, heavy objects.
The first stage of the BugJuggler project will be construction of a working 8ft tall single arm proof-of-principle juggler able to toss and catch a 250lb mass... (cont'd)
A Robot Valet Will Park Your Car at This German Airport
Last week, Düsseldorf airport (DUS) introduced robot valets to take the hassle out of parking for travelers. Travelers can leave their cars at the arrival level of the ParkingPLUS structure. As they leave, they confirm on a touch-screen that no one is in the car.
The robot valet, nicknamed "Ray," takes it from there. The robot measures the vehicle, picks it up with a forklift-like system, and takes it to the back area, where it will position it in one of the 249 parking spots reserved for automated valets.
The machine is capable of carrying standard cars weighing up to 3.31 tons. The robot valet is even connected to the airport's flight data system, and by checking customer trip data with the database, Ray knows when the customer will return for the vehicle. A traveler can note any itinerary changes in a parking app, which is available for iOS and Android.
Records 1306 to 1320 of 1601
First | Previous | Next | Last
Featured Product
CMES - AI-Powered 3D Robot Vision
Powered by AI, CMES Robotics enables 3D vision for factory robots. CMES AI vision software enables robots to recognize unstructured, flexible, or deformed objects, pick them up, and loading and unloading. CMES Vision software has been deployed worldwide for random palletization and depalletization along with void filling applications. CMES Robotics automates your warehouse, logistics, and supply chain. For more information, please visit: cmesrobotics.com or email info@cmesrobotics.com.